I-7565
I-7565

CAN (Controller Area Network) is a serial bus system especially suited to structure intelligent industry devices networks and build smart automatic control systems. The I-7565 is a cost-efficient device for coupling the CAN-bus to the PC using the standard USB interface by the MS-Windows 98, Me, 2000, XP, Win 7 and Win 10 operating systems. If you establish the connection between the I-7565 and the PC during the runtime of the computer, the PC automatically loads the relevant device driver (hot plug & play).

 

Request For Quotation


    Category:

    Description

    The following figure shows the application architecture for I-7565 modules. The PC can be the CAN host, monitor or HMI to access/control the CAN device through the CAN network by the I-7565 Converter. This module let you to communicate with CAN devices easily from PC with USB interface.

    3000V isolation on CAN side
    The CAN port of I-7565 is an isolated with 3000V isolation. This isolation can protect the local devices from the damage signal coming from CAN network.

    Watchdog inside
    The I-7565 Watchdog is a hardware reset circuit to monitor the I-7565’s operation status. When working in harsh or noisy environment, the I-7565 may be down by the external signal. The circuit may let the I-7565 to work continuously and never halt.

    Power and Error indicator display
    There are two indicators on the I-7565.The power indicator can help user to check whether the I-7565 is standby or transmitting/receiving messages. The Error indicator will be turned on when some errors occur on the I-7565.

     

    Applications

    • Factory Automation
    • Building Automation    
    • Home Automation    
    • Control System    
    • Monitor System
    • Vehicle Automation

     

     

    Features

    • RoHs Design
    • Fully compliant with USB 1.1/2.0(Full Speed)
    • Fully compatible with the ISO 11898-2 standard
    • No external power supply is required as I-7565 takes it’s power from the USB bus
    • 82C250 CAN transceiver
    • Transmission speed up to 1M bps for CAN and 921.6K bps for USB
    • Support both CAN 2.0A and CAN 2.0B
    • Built-in jumper to select 120 ohm terminal resister
    • Power, data flow and error indicator for CAN and USB
    • 1000 frames in CAN received buffer
    • Watchdog inside
    • Windows 98/ME/2000/XP/Vista/Win 7/Win 10 and Linux drivers support
    • Supports a range of baud rates from 10 kbps ~ 1 Mbps
    • Able to configure the CAN baud rate for each channel using a rotary switch
    • Extends the CAN transmission distance

    Note: We have verified to drive 100 CAN nodes at the same time via one CAN port of I-7565.

     

    Utility

    • CAN bus Baud rate configuration
    • CAN acceptance filter configuration
    • CAN2.0A or 2.0B specific selection
    • Checksum and Error Response settings
    • Easy test to transmit/receive CAN messages

    CAN Monitor & Datalog Tool

    • It has a CAN message field which can display the receiving CAN messages in
    • Decimal or HEX mode
    • Can display the timestamp of each received CAN message
    • Users can change the display mode, up-down, down-up or stop
    • It can count the number of received CAN messages
    • Data Log : It can save the CAN message as “ txt ” file
    • Has CAN ID filter function
    • Can send CAN message to CAN BUS according the defined interval time

    Hardware Specifications

    Hardware
    EEPROM
    2 KB (for system information), 100,000 erase/write cycles
    CAN Interface
    Port Channels
    1
    Transceiver
    82C250/TJA1042
    Connector
    9-pin male D-Sub (CAN_L, CAN_SHLD, CAN_H, N/A for others)
    Baud Rate
    10 k, 20 k, 50 k, 125 k, 250 k, 500 k, 800 k, 1 Mbps (allow user-defined CAN baud rate)
    Isolation
    3000 Vrms on the CAN side
    Terminal Resistor
    Selectable 120 Ω terminal resistor by jumper
    Support Protocol
    CAN 2.0A/2.0B
    Receive Buffer
    1000 data frames
    UART Interface
    Connector
    USB Type B
    Baud Rate
    110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 bps
    Compatibility
    USB 1.1 and 2.0 standard
    Receive Buffer
    900 data frames
    Power
    Power Consumption
    1.5W
    LED
    Round LED
    ON LED: Power and Data Flow; ERR LED: Error
    Mechanism
    Installation
    DIN-Rail
    Dimensions
    72mm x 112mm x 33mm (W x L x H)
    Environment
    Operating Temp.
    -25℃ to 75℃
    Storage Temp.
    -30℃ to 80℃
    Humidity
    10~90% non-condensing

    Hardware Structure

    Wire Connection

    Pin Assignment

     

    Internal Structure

    Ordering Informations

    I-7565-G CR
    		 Intelligent USB to CAN converter (RoHS)
    Include Cable
    		 CA-USB18(1.8M Cable)x1

    Datasheet

    Related products